SONAX PROFILINE CeramicCoating "CC" Pro (Paint) ceramic coating 50ml

Professional ceramic coating for up to 4 years of paint protection — SONAX PROFILINE CeramicCoating CC Pro

What does the SONAX PROFILINE CeramicCoating CC Pro do? This one-step professional ceramic coating for paint protects for up to 4 years against UV, chemicals and the weather — with extreme hydrophobicity, gloss boost and hardness in a single coat.

If you work in professional detailing and you want a long-lasting protection solution that goes down in a single coat yet still delivers the performance of a real ceramic coating, the SONAX PROFILINE CeramicCoating CC Pro is exactly the product you're after. This one-step ceramic coating for paint builds a glass-like SiO₂-based protective layer on the surface that shields the paint for up to 4 years against UV, acid rain, fallout, chemicals and mechanical wear. At the same time the ceramic layer noticeably lifts the gloss and the colour depth of the paint — an optical effect that visibly beats the car's starting condition and that your customers pick up on straight away. The 50 ml kit, complete with 4 application pads, holds enough material for a full mid-size car when you dose it sensibly.

• Up to 4 years of lasting protection in a single coat. The CC Pro is built as a one-step ceramic coating — one layer is all it takes to trigger the full protective effect. Unlike two-step systems, there's no separate promoter step, which cuts the total working time on the coating job. Up to 4 years from a one-step ceramic coating is a strong claim — and it assumes the paint is fully decontaminated, polished and degreased before you lay the product down, so the CC Pro bonds straight to flawless clear coat. With proper prep and regular care (pH-neutral washes, a periodic ceramic top-up), 3 to 4 years of life is realistic.
• Extreme hydrophobicity and a self-cleaning effect once it has cured. SiO₂ ceramic coatings create a superhydrophobic surface where water beads up into near-perfect spheres and drags dirt particles off with it. With the CC Pro this lotus effect is especially strong thanks to the high SiO₂ concentration in the formula: water doesn't cling to the surface, it rolls straight off. Day-to-day that means fewer water spots after a wash, easier drying and less dirt sticking to the paint. After the ceramic coating the car simply stays cleaner between washes than it would without it.
• Higher surface hardness as a guard against micro-scratches and chemical attack. Once cured, the CC Pro's ceramic layer reaches a hardness well above that of the clear coat — typically 9H or more on the pencil-hardness scale. That hardness protects the paint against micro-scratches from everyday contact like wiper-blade action, automated car washes or dusting off. Chemical resistance against acid rain, bug splatter, bird droppings and industrial fallout is clearly improved over unprotected paint too — aggressive substances can attack the ceramic layer, but they can't eat through to the clear coat anywhere near as fast as on an unprotected car.

Detailing1's tip from the shop: The CC Pro forgives nothing when it comes to surface prep — lock holograms, scratches or contamination under the ceramic layer and you've preserved them for years. The full prep protocol runs like this: decontamination (iron remover, tar remover), wet-sanding or a correction stage to pull out scratches, then a finishing polish (e.g. SONAX PROFILINE PerfectFinish) for a mirror-flat base, then an IPA wipe to degrease. Only then do you lay the CC Pro down in thin, even passes — keep it from pooling on edges. Work panels no larger than 50×50 cm, watch the dwell time (per the maker's spec), then buff it off with a clean microfibre cloth before the product flashes off. To maintain the finished ceramic layer we recommend the SONAX PROFILINE Ceramic SprayCoating as a periodic topper after every wash — it wakes the beading back up and stretches the life of the CC Pro considerably.

SiO₂ ceramic chemistry explained — how the CC Pro builds paint protection on a molecular level

Ceramic coatings like the SONAX PROFILINE CeramicCoating CC Pro work in a fundamentally different way to waxes or polymer sealants. Waxes and polymers sit as a film on top of the paint, hold on through physical adsorption and get worn down by washes, UV and mechanical contact over weeks to months. Ceramic coatings, on the other hand, react chemically with the paint — the SiO₂ compounds in the CC Pro condense on the clear coat into a covalently bonded glass layer that simple washing or UV can't break down. Only mechanical removal (polishing) or chemical attack at a very low or very high pH will touch the fully cured layer.

The curing process starts the moment you apply the CC Pro and runs 24 to 72 hours for the initial cure, depending on ambient temperature and humidity. The ceramic layer reaches full final hardness after about 7 to 14 days — and during that window you want to keep the car away from harsh weather or aggressive chemicals as much as you can. Ideally you park the coated car indoors or under cover for the first few days. Washes in the first 7 days should be gentle (a hand wash with a rinse only, no pressure washer straight at the surface) so the cure isn't disturbed.

The SiO₂ concentration in the CC Pro is tuned for a one-step system: too low and you'd lose protection and durability; too high and application gets harder, with the risk of streaking or high-gloss inconsistencies. SONAX has dialled this balance in the CC Pro to suit the way experienced detailers work — a product built for performance that still gives you repeatable results when you use it properly. The optimised flash-off time after application lets you keep a smooth rhythm even on bigger cars.

Applying the CC Pro the right way — the full workflow from prep to cure

The application workflow for the SONAX PROFILINE CeramicCoating CC Pro breaks down into three phases: prep, apply and cure. The prep phase decides the long-term result: first, fully decontaminate the paint — break down iron particles with an iron remover, treat tar spots with a tar remover, remove lime deposits. Then the correction stage: for paint in normal condition the SONAX PROFILINE PerfectFinish as a finishing polish is enough; for heavily scratched paint, run a compound step first with the FS 05-04 or the CutMax. After polishing: an IPA wipe (isopropyl alcohol 1:1 with water) over every panel to strip out oils, polish residue and grease for good. When you apply the CC Pro the paint surface has to be absolutely oil-free and clean.

Applying: wet the supplied application pad with 2 to 3 drops of CC Pro — no more. Ceramic coatings are concentrated and less is more: a thin, even film bonds better than a heavy layer and comes off more easily. Work panel by panel in crosshatch passes (horizontal + vertical), with overlapping strips of about 3 to 4 cm. Mask edges and trim with tape, or pull residue off straight away with a swab — ceramic that gets onto edges and into gaps cures hard and forces aggressive rework. Watch the dwell time and swap your cloth as soon as it starts dragging.

Cure and aftercare: keep the car away from rain and moisture for at least 24 hours; first wash no sooner than 48 to 72 hours; full mechanical durability after 7 days. No wax, no silicone spray, no acidic or alkaline cleaners in the first 14 days. After that the car is cleared for normal pH-neutral washes — the long-term care cycle is regular hand washes with a pH-neutral shampoo plus a periodic top-up with a ceramic-friendly topper spray.

Where the CC Pro fits — which cars and customers get the most out of a ceramic coating

The CC Pro suits any car where you want multi-year protection with minimal ongoing upkeep. A ceramic coating pays off most on new cars — here the paint is protected from day one, before scratches, oxidation and contamination get a chance to take hold. For customers who treat their car as an investment or want to keep it spotless, the ceramic coating is by far the most economical long-term option: one application every 4 years replaces a string of yearly polymer sealant treatments.

For workshops and detailing studios the CC Pro is an attractive premium service: the value to the customer is felt directly (gloss, beading, a protection promise), the margin per job is good, and with consistent prep the product delivers repeatable results. The single 50 ml size with 4 pads is designed for one car and makes job costing clean: one kit = one car. In the shop, store the CC Pro cool and dry; once opened, keep any leftover in the sealed original bottle to keep moisture out, since moisture pre-activates the ceramic chemistry.

For leased and company cars the CC Pro is especially worth it: the paint stays in better shape across the whole lease term (typically 2 to 4 years) — fewer scratches, less oxidation, easier washing — which means fewer charge-backs from the lessor at hand-back. A one-off coat at vehicle hand-over pays for itself fast once you weigh it against the cost of professional paint correction at lease end.

CC Pro vs. CC One vs. CC Evo — ceramic coating comparison in the SONAX PROFILINE range

The SONAX PROFILINE CeramicCoating range has the right answer for different needs. The SONAX PROFILINE CeramicCoating CC One is the entry-level ceramic coating in the range: at 40 ml with 2 application pads, cheaper and simpler to use, with shorter protection (about 12 to 24 months) — ideal for anyone getting their first taste of ceramic coatings or coating cars they won't keep for long. The SONAX PROFILINE CeramicCoating CC Pro is the step up in protection (up to 4 years) and SiO₂ concentration — a product for experienced users who expect more from long-term protection and the look.

The SONAX PROFILINE CeramicCoating CC Evo, finally, is the flagship system in the SONAX PROFILINE ceramic range: a two-step system (promoter + main coating) for maximum bonding and maximum protection life, built for the cases where only the best result will do — show cars, high-value vehicles, customers with the highest standards. The CC Evo takes more time and experience to apply, but it delivers a result that goes beyond the CC Pro. For the bulk of professional detailing jobs the CC Pro is the optimal product on both cost and quality — it bridges the gap between the accessibility of the CC One and the performance of the CC Evo.

Buying the SONAX PROFILINE CeramicCoating CC Pro — contents, who it's for and our take

The SONAX PROFILINE CeramicCoating CC Pro comes as a complete kit with 50 ml of ceramic coating and 4 application pads. The kit is sized for one car — on cars up to mid-size the contents comfortably cover every exterior surface (roof, bonnet, wings, doors, rear, bumpers). On bigger vehicles (SUV, van, transporter) we'd suggest dosing very sparingly or keeping a second kit on hand. The 4 application pads supplied are meant for different surfaces and should be swapped regularly — a saturated pad spreads the CC Pro unevenly.

Who the CC Pro is for: professional detailers with ceramic coating experience; workshops offering ceramic coating as a premium service; car dealers who want to deliver new cars with long-term protection; and ambitious home users with experience in car care and the right tools for the prep (polisher, IPA, microfibre cloths). Don't reach for the CC Pro without proper prep — the product needs a flawless, degreased paint surface.

Bottom line: if you want to coat a car with lasting, professional ceramic protection and you take the prep seriously, the SONAX PROFILINE CeramicCoating CC Pro gives you a strong, proven product with excellent value in the premium bracket. Four years of paint protection from a single application — that's the CC Pro's promise, and it delivers on it when you use it properly.