{"product_id":"flex-ppf-finish-polierpad","title":"\"PP-F\" Finish Polishing Pad","description":"\u003ch2\u003eFLEX PP-F Finish Polishing Pad — soft finishing pad for maximum gloss and a hologram-free finish\u003c\/h2\u003e\n\u003cblockquote\u003e\n\u003cp\u003e\u003cem\u003eWhat is the FLEX PP-F finishing pad? The FLEX PP-F is a soft, white foam polishing pad with reticulated foam — built as the final finishing step in the three-step FLEX polishing system for maximum gloss, complete freedom from holograms and a clear, mirror-like paint surface on FLEX polishers.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003cp\u003eThe last step in the polishing process decides whether a result is truly professional. The \u003cstrong\u003eFLEX PP-F finishing pad\u003c\/strong\u003e is that last step: a soft, white pad that polishes the surface to a high gloss with a fine finishing polish, clears every hologram left over from the compound step and leaves a clear, deep-gloss paint surface — ready for a sealant or a coat of wax.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX PP-F\u003c\/strong\u003e is cut from the same reticulated foam as the PP-C and PP-M, but in a much softer formulation. That softness isn't a shortfall in quality — it's the key property for the finishing step: a soft pad builds up minimal heat, transfers minimal pressure and works the finest finishing abrasives gently and evenly into the paint. The result is a gloss you simply can't hit with hard pads.\u003c\/p\u003e\n\u003cp\u003eAs the third step in the \u003cstrong\u003eFLEX PP-Pad system\u003c\/strong\u003e (PP-C for cut, \u003ca href=\"\/en\/products\/flex-pp-m-universal-polierpad\"\u003ePP-M for compound\u003c\/a\u003e, PP-F for finish), the PP-F plays a clear and irreplaceable role. What the PP-C starts with aggressive cut and the PP-M carries on with compound refinement, the PP-F finishes off: the paint is brought to the state where the car can be handed back to the customer or prepped for a protective sealant.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSoft foam for maximum gloss without holograms — the finishing standard in the three-step protocol.\u003c\/strong\u003e The softness of the PP-F foam body is the technical core of what it does: soft foam cushions the pressure from the polisher, dials abrasive aggression down to a minimum and, at the same time, lets the finest polishing particles glide evenly across the paint. The result: no fresh holograms, no buffer trails, no hazy film — just clear, deep gloss.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReticulated foam for even finisher release — controlled polish delivery right down to the last pass.\u003c\/strong\u003e The reticulated foam body of the PP-F picks up finishing polish precisely and releases it evenly throughout the whole polishing run. That stops the polish drying out in the pad and the patchy finish that comes with it. For the finishing step, where even results across the whole panel are what count, this steady release is the pad's most important performance factor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAvailable in Ø150mm and Ø125mm, each as a 2-pack and 5-pack — finishing quality for every FLEX polisher.\u003c\/strong\u003e The PP-F comes in two diameters: Ø150mm for the \u003ca href=\"\/en\/products\/flex-xfe21518ec-15mm-akku-exzenterpolierer-freilauf-150mm-18v\"\u003eFLEX XFE 2 15\u003c\/a\u003e and other 150mm dual-action polishers, Ø125mm for 125mm machines. As a 2-pack or 5-pack — for pro work with several cars a day the 5-pack is the smarter buy, since a fresh finishing pad per car keeps results consistently high.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cblockquote class=\"praxistipp\"\u003e\n\u003cp\u003e\u003cstrong\u003eDetailing1's tip from the shop:\u003c\/strong\u003e For the PP-F finishing step we'd go lighter on the finisher than in the compound step. The soft PP-F spreads product more efficiently than hard pads — too much polish gives you streaks and a longer dry time. Sweet spot: a small dab of finisher on the pad, spread it at low speed, then bring it up to a medium working speed. After the last pass, always check the result under an inspection light before you lay down a sealant or wax — the PP-F gives its best when the compound step before it is fully finished.\u003c\/p\u003e\n\u003c\/blockquote\u003e\n\u003chr\u003e\n\u003ch3\u003eFoam softness and gloss performance — why finishing pads have to be soft\u003c\/h3\u003e\n\u003cp\u003eThe physics of the finishing step is the opposite of the cut step: where hard foam transfers mechanical pressure into the paint on the cut step and pulls scratches out by cutting, the finishing step asks for exactly the reverse. The \u003cstrong\u003eFLEX PP-F finishing pad\u003c\/strong\u003e is soft because only soft foam spreads the abrasives in a fine finishing polish evenly enough across the surface that no new micro-holograms show up.\u003c\/p\u003e\n\u003cp\u003eA hard pad with a fine finisher would drive the abrasives too hard into the paint and leave a fine but visible hologram pattern — the very problem the compound step is meant to clear. The soft PP-F kills that effect completely: the abrasives glide gently over the surface, polish to a high gloss and leave no trails of their own.\u003c\/p\u003e\n\u003cp\u003eHeat build-up on the PP-F finishing step is much lower than on the PP-C cut step. The soft foam soaks up part of the machine's energy instead of sending it all into the paint. That's what you want on the finishing step: low temperatures protect the polished surface and let you work longer without risk on heat-sensitive paints.\u003c\/p\u003e\n\u003cp\u003eThe white colour of the PP-F is the international code colour for finishing pads in the FLEX system. White says: soft material, minimal cut, maximum gloss. In the three-step protocol the colour coding is a handy bit of order: red for PP-C (cut), orange for PP-M (compound), white for PP-F (finish) — no grabbing the wrong pad, even when the case is full.\u003c\/p\u003e\n\u003cp\u003eOne more thing about pad softness that often gets underrated: the PP-F is a great fit for older or thinner clear coats, where finishing with a harder pad carries a raised risk of burning through. If you don't know exactly how much clear coat is left on a car — paint thickness under 80 microns is nothing unusual in restoration work — the soft PP-F keeps you on the safe side. Less pressure, less cut, less risk — with no compromise on the final gloss.\u003c\/p\u003e\n\u003ch3\u003eUsing the PP-F in the three-step protocol — the decisive final step\u003c\/h3\u003e\n\u003cp\u003eThe finishing step with the \u003cstrong\u003eFLEX PP-F finishing pad\u003c\/strong\u003e is the shortest, but not the least important step in the three-step protocol. It decides the final look: whether the paint comes out clear and mirror-like after the work, or whether a fine haze or holograms cloud the result.\u003c\/p\u003e\n\u003cp\u003eA good PP-F result needs a fully finished compound step with the PP-M first. If fine holograms are still showing under the inspection light after the PP-M, the PP-F can't fully clear them — it isn't built for that. The PP-F refines a surface that's already well prepped; it doesn't fix incomplete earlier steps. The division of labour in the FLEX PP system is clearly set here and you stick to it.\u003c\/p\u003e\n\u003cp\u003eWorking the PP-F on FLEX machines, we'd say: small dab of finisher on the pad, work at a medium speed — the PP-F doesn't need high speed to do its job. Two to three overlapping passes per section, light pressure, no dwelling in one spot. The tell for a good finishing step: the finishing polish disappears completely on the surface without drying out. If it dries too fast, you laid down too little; if it leaves streaks, you laid down too much.\u003c\/p\u003e\n\u003cp\u003eThe check after the PP-F finishing step matters: under an inspection light, ideally a full-spectrum light with high CRI, you check the finished surface for leftover holograms and buffer trails. A good PP-F result shows a clear, even reflection with no visible pattern. If dark areas still show fine holograms, either the compound step was incomplete or too little finisher went on. In that case: work the same area again with the PP-F and enough finisher — no going back to the PP-M if the rest of the surface is already hologram-free.\u003c\/p\u003e\n\u003cp\u003eThe PP-F can also be used as a final care pad on well-kept cars where no scratch correction is needed: a regular refresher polish with the PP-F and a mild finishing product keeps the gloss up and clears a light oxidation film without any cut or compound step. For cared-for cars that get worked regularly, that makes the PP-F a sensible buy on its own too.\u003c\/p\u003e\n\u003ch3\u003ePP-F sizes and compatibility — Ø125mm and Ø150mm on the FLEX hook-and-loop system\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX PP-F finishing pad\u003c\/strong\u003e shares its hook-and-loop mounting with the PP-C and PP-M: the same standardised backing plate, the same swap system. That lets you switch pads between all three steps fast, no tools and no lost time. In practice: once you've worked a panel on the cut step, you can run the PP-M and PP-F on the same panel straight after, without re-rigging the machine.\u003c\/p\u003e\n\u003cp\u003eThe Ø150mm version is compatible with the \u003ca href=\"\/en\/products\/flex-xfe21518ec-15mm-akku-exzenterpolierer-freilauf-150mm-18v\"\u003eFLEX XFE 2 15 cordless dual-action polisher\u003c\/a\u003e and other 150mm polishers in the FLEX line. The Ø125mm version fits the more compact 125mm machines. For the \u003ca href=\"\/en\/products\/flex-pxe8012ec-akku-exzenterpolierer-80mm-12v\"\u003ePXE 80\u003c\/a\u003e the PP-F in the standard sizes on offer isn't the first choice — here the matching small-pad format is what you want for the finishing step.\u003c\/p\u003e\n\u003cp\u003eThe 5-pack makes real sense for the finishing step in particular: since the PP-F is the last pad in the chain and defines the final surface, a clean, fresh pad per car matters more on the finishing step than on any other. Grit carried over from the compound step or dried finisher left in the pad feeds straight into how even the gloss comes out.\u003c\/p\u003e\n\u003ch3\u003ePP-F compared — finishing pad against universal pad and cut pad\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX PP-F finishing pad\u003c\/strong\u003e is the specialist end of the FLEX PP-Pad range. Where the PP-C is built for maximum cut and the PP-M for balanced compound work, the PP-F has one goal only: the best possible surface gloss with complete freedom from holograms. That focus makes it a must for anyone chasing professional results — and skippable for anyone who just wants a quick one-step pass.\u003c\/p\u003e\n\u003cp\u003eFor the one-step approach the PP-F is the wrong pick: it has too little cut to clear scratches or oxidation. If you polish in one step, you grab the PP-M as the more universal pad. The PP-F only makes sense as the last step in a multi-step protocol — and in that role it's irreplaceable.\u003c\/p\u003e\n\u003cp\u003eCompared with generic finishing pads from other makers, the PP-F is part of a thought-out system: it's matched to the pad sizes and backing plate of the FLEX machines, and its foam hardness is tuned to work with the PP-C and PP-M. Run the full FLEX PP system and you've got a consistent, matched polishing programme — not a pile of pads thrown together at random. That's the difference between a protocol that delivers predictable, repeatable results and one that shifts with every pad combo.\u003c\/p\u003e\n\u003ch3\u003eBuying the FLEX PP-F — recommendations for pro use and the complete pad set\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eFLEX PP-F finishing pad\u003c\/strong\u003e is the last investment for a complete FLEX PP system. If you already run the PP-C and PP-M, you close out the set with the PP-F and have a complete three-step polishing programme that suits every paint condition and every correction level.\u003c\/p\u003e\n\u003cp\u003eOur pick for the full set: \u003ca href=\"\/en\/products\/flex-pp-c-cut-polierpad\"\u003ePP-C in the 5-pack\u003c\/a\u003e (cut), \u003ca href=\"\/en\/products\/flex-pp-m-universal-polierpad\"\u003ePP-M in the 5-pack\u003c\/a\u003e (compound) and PP-F in the 5-pack (finish) — this set covers a full polishing season for pro use. Or one 2-pack of each for the beginner who wants to get to know the three-step protocol first, before moving up to the 5-packs.\u003c\/p\u003e\n\u003cp\u003eThe PP-F is compatible with the \u003ca href=\"\/en\/products\/flex-bpmpxe-klett-teller\"\u003eBP-M PXE backing plate\u003c\/a\u003e for the PXE 80 as well as all standard backing plates for 125mm and 150mm FLEX polishers. Switching between the PP-C, PP-M and PP-F takes seconds — exactly the efficiency that counts in pro use. Three pads, three steps, one flawless result.\u003c\/p\u003e\n","brand":"FLEX","offers":[{"title":"Ø150mm \/ 2 pieces","offer_id":57377320173903,"sku":"D1-FLEX-532407","price":42.91,"currency_code":"EUR","in_stock":false},{"title":"Ø150mm \/ 5 pieces","offer_id":57377320206671,"sku":"D1-FLEX-532655","price":105.6,"currency_code":"EUR","in_stock":false},{"title":"Ø125mm \/ 2 pieces","offer_id":57377320239439,"sku":"D1-FLEX-532408","price":40.26,"currency_code":"EUR","in_stock":false},{"title":"Ø125mm \/ 5 pieces","offer_id":57377320272207,"sku":"D1-FLEX-532656","price":99.0,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0800\/3272\/7375\/files\/pp-f-polierpad-150mm.png?v=1775062567","url":"https:\/\/detailing1.at\/en\/products\/flex-ppf-finish-polierpad","provider":"Detailing1","version":"1.0","type":"link"}